亚洲精品鲁一鲁一区二区三区-最爽无遮挡行房视频-强壮的公次次弄得我高潮A片日本-精品人妻无码一区二区三区换脸-中文字幕亚韩-亚洲国产精品一区二区第一页-丰满岳乱妇一区二区三区-大陆极品少妇内射AAAAAA-国产乱人伦AV麻豆网-AV国産精品毛片一区二区三区-午夜精品视频在线无码-免费精品一区二区三区A片在线-在线天堂无限次观看,亚洲日韩无码一区二区,中文字幕乱人伦视频在线,亚洲欧美熟妇综合久久久久久,少妇无码一区二区三区免费久久,欧美黑人一级片在线观看,久久久精品无码一区三区,国产视频在线观看蜜芽,大香蕉五月婷婷精品视频 ,久草精品在线,国产无码在线播放一区二区,囯产无码交换大片在线播放,八戒八戒在线高清观看视频 ,娇妻被又粗又长又猛玩,国产曰肥老太婆无遮挡,国产剧情黄色,国产成年无码久久久久毛片資訊,大香蕉太香蕉成人现现,逼逼爱爱爱无码免费观看,亚州色图欧美图片自偷自拍,碰碰视频麻豆,午夜一本,一起射综合影院,黑人干熟女,欧洲高清转码区一二区 ,国产高清视频色拍,粉嫩无码小泬无套在线观看,大香蕉在线网站,成人做爰理论片,成人漫,9l视频自拍九色9l成人

The main structural components of the fan are impeller, casing, air inlet, bracket, motor, pulley, coupling, muffler, transmission parts (bearings), etc. The unpowered fan uses the air heat convection caused by the natural wind and the indoor and outdoor temperature difference to drive the turbine to rotate so as to use the centrifugal force and negative pressure effect to exhaust the indoor fresh hot air.

風機關系到系統的輸配能耗，是建筑節能非常關鍵的部分。根據國家空調設備質量監督檢驗多年風機檢測表明很多風機在額定工況下都存在問題，因此需要嚴格按照產品標準要求生產和制造風機。風機剛開始工作時軸承部位的振動很小，但是隨著運轉時間的加長。

Fan is related to the energy consumption of transmission and distribution of the system, and is a very important part of building energy saving. According to the national air conditioning equipment quality supervision and Inspection Center for many years, fan testing shows that many fans have problems under rated conditions, so it is necessary to produce and manufacture fans in strict accordance with product standards. At the beginning of the fan, the vibration of the bearing is very small, but it increases with the running time.

風機內粉塵會不均勻的附著在葉輪上，逐漸破壞風機的動平衡，使軸承振動逐漸加大，一旦振動達到風機允許的值11mm/s時（用振幅值表示的允許值如下），風機必須停機修理（清除粉塵堆積，重做動平衡）。因為這時已是非常危險的，用戶千萬不可強行使用。在風機振動接近危險值時，有測振儀表的會報警。

The dust in the fan will adhere to the impeller unevenly, and gradually destroy the dynamic balance of the fan, so that the bearing vibration will gradually increase. Once the vibration reaches the maximum value of 11mm / s allowed by the fan (the maximum allowable value expressed by the amplitude value is as follows), the fan must be shut down for repair (remove the dust accumulation, and do the dynamic balance again). Because it is very dangerous at this time, users must not use it forcibly. When the fan vibration is close to the dangerous value, the vibration measuring instrument will give an alarm.

風機的軸承溫度正常時為≤70℃，如果一旦升高到70℃，有電控的應（會）報警。此時應查找原因，首先檢查冷卻水是否正常？軸承油位是否正常？如果一時找不到原因，軸承溫度迅速上升到90℃，有電控的應（會）再次發出報警、停車信號，風機開車、停車或運轉過程中，如發現不正常現象應立即進行檢查，檢查發現的小故障應及時查明原因設法消除。

When the bearing temperature of the fan is normal, it is ≤ 70 ℃. If it rises to 70 ℃, the fan with electric control shall (will) give an alarm. At this time, the reason should be found out. First, check whether the cooling water is normal? Is the bearing oil level normal? If the cause cannot be found for a while, the bearing temperature will rise rapidly to 90 ℃. If there is electric control, the alarm and stop signal shall be sent again. In the process of fan start-up, stop or operation, if abnormal phenomenon is found, it shall be checked immediately, and the small fault found in the check shall be found out in time to eliminate the cause.